The biodegradable, non-flammable, non-toxic, concentrated surfactant system. With both Hydrophilic and oleophobic properties.
It has Excellent emulsion-breaking capability used for a broad range of applications.
This video clip shows OSS solution being applied to treat and clean used drums with machine oil residue which are very hard to clean without using chemical cleaners. This shows how OSS is effective at removing these oil residues.
- Degreaser & De-oilier
- Soil wash to remove hydrocabons
- Use to remove PCBs from surfaces by pressure sprays
- Cleaning Baker's and Frak's tanks
- Decanting water and sludge
- Cleaning of most industrial equipment (OSS is "non-corrosive")
- Walls, floors, bathrooms & machinery
- Use in dip tanks
- Use in hot part waters
- Use in waste water to drop solids, separate oil, grease and water
- Bilge water and oil/water separator
- Fuel tank cleaner ( OSS is "non combustible")
- Deck Cleaner, bathrooms, galleys and even laundry!
- Spraying down hull in dry dock
- Cleaning diesel engines
- Salt water as well as fresh water can be used to activate OSS
Ideally suited for cleaning protective coatings and grease and grime off of new or used parts. OSS works in parts washing devices without modifications of the equipment and leaves no residue after
Oils and greases are forced to float to the surface of the cleaning solution and can be skimmed off for recovery and recycling. Remaining precipitated solids are cleaned of hydrocarbons
Effectively removes oils, greases, and accompanying dirt from most surfaces. Can be applied mopping, with floor cleaning machines, or with low or high-pressure spray. OSS is also an effective
internal cleaner of hydraulic and lubrication systems, removing hydrocarbon and corrosive build-ups.
OSS is an excellent choice for cleaning ferrous metal parts to be painted later.
oils and grease from parts, flash rusting while drying is prevented by OSS leaving an invisible barrier that provides extended corrosion protection. This barrIer can be painted over without additional rinsing.
Superior paint adhesion is obtained by cleaning parts in a OSS solution. Methods of cleaning vary between hand application, heated dip tanks, or pressure washing.
OSS is also an excellent choice for cleaning prior to powder coating parts.
Effectively separates oil, water, and solids in conveyer traps and floor sumps. Cleaned metal dust,
shavings and dirt are precipitated to the bottom, the solution of OSS and water forms a barrier in the
middle, and hydrocarbons are forced to float on the top. The efficiency of oil/water separators in plant
waste treatment systems are significantly increased. The amount of toxic waste requiring disposal
after treatment is also reduced. The solution of OSS and water can be reused to treat more waste
materials until biodegradation occurs and it no longer effectively forces oil and water to separate.
Cleans oil, grease, carbon deposits, and dirt in engine rooms and cargo holds, on bulkheads and
decks, and in crew living and duty quarters. Lifts and removes oil and grease that has been baked on
to hot engine parts, steam lines, etc. An ideal non- corrosive cleaner for reusable filters in engine oil
and lubrication systems. Salt water as well as fresh water can be used to activate OSS
Increases the effectiveness of oil/water separation systems and extends the life of disposable filters.
Completely separates oil from oil/water emulsions in the bilge. Solids in bilge (both settled and
suspended) will be cleaned of hydrocarbon contamination and suspended solids will be precipitated
to the bottom of the bilge. Salt water as well as fresh water can be used to activate OSS.
When injected into wells, OSS maintains the crude in a fluid state even at reduced temperatures and
pressures following treatment. It also relieves clogs due to drilling mud accumulation. Does not
physically or chemically alter the crude oil. Will increase flow rates by migrating into the oil-bearing
strata and lifting crude oil trapped in the pores of the rock or sedimentary formation. Does not add to
hazardous waste disposal problems.
Does NOT allow oil and water to mix and maintain crude oils in a liquid state, even at reduced
temperatures. Keeps lines and pumps cleaner, boosting flow and cutting maintenance costs. Causes
entrained water and inorganic solids to separate from the crude oil, providing a higher-grade product
at the refinery/terminal.
Cleaning Oil and Sludge Storage Tanks/Pits
Cleans tank walls using normal spray cleaning equipment and does not alter the composition of the recovered product.
The chemical process separates sludge into three components:
• Cleaned precipitated solids with low toxicity on the bottom
• A barrier solution of water and the OSS product compose the middle layer
• Separated oil on the top layer that can be recovered and recycled.
This process does not create explosive gases or caustic fumes or mist. Final bacterial remediation
can be speed up by a factor of 10 or more.
Removes more than 95 percent of the hydrocarbons from contaminated soils in the first-stage process. Recovered oils may be recycled.
Water component requires little, if any, predisposal processing. Total time required for complete remediation is reduced from years to weeks.